High Speed Automatic Nail Making Machine

Equipment introduction

Our high speed nail making machine introduces the European advanced technology, after decades of innovation and development, the quality of equipment is stable and reliable, eliminating the long and short nails, aircraft head, crooked caps, nail caps of different sizes, bent nails and other quality problems. The main bearing using Japan NSK original imported bearings, the use of more than 7 years without problems! Equipment operation is extremely simple, an ordinary worker training time of 2 days can smooth operation, let nail factory completely get rid of the dependence on the nail workers. The equipment energy consumption is low and the production cost is greatly reduced. The company has established a complete process quality control system! 100% inspection of all raw materials and parts! At present, our high-speed nail making machine occupies more than 95% of the domestic market and occupies a large share of the export market, about 85%, which has been exported to the United States, Europe, the Middle East and other regions. Average annual sales of more than 600.

Equipment advantage

1.Production of one ton of ordinary loose nails can save :

Reduce labor cost 66% above, estimate $3；

30-60 KWH can be saved per ton of nails ，Save $4- $6 on electricity. For example: 2.2mm *50mm nail, with the ordinary nail machine in accordance with the actual power of 2.5kw calculation, about the need for electricity 96.52 KWH; Using our high-speed nail making machine, according to the actual operation of 3.8Kw calculation, about the need for electricity 53.9 KWH, the actual saving of electricity up to 42.62 KWH;

The waste nail loss is reduced to about 1%, about $5;

The consumption cost of mold, nail cutter and punch should be reduced by more than 70%, at least 2-3 dollars per ton. The conservative estimate is that the cost per ton of nail can be saved: 3+4+5+2=14 dollars per ton;

If it can be made from clean steel wire, there is no need to wash the nails，You can save about $5 per ton,This reduces the production cost per ton: 14+5= $19.

2.The produced nails are used to make roll nails, paper row nails or plastic row nails, saving per ton of nails:

Reduce labor cost 66% above, estimate $3；

30-60 KWH can be saved per ton of nails ，Save $4- $6 on electricity. For example: 2.2mm *50mm nail, with the ordinary nail machine in accordance with the actual power of 2.5kw calculation, about the need for electricity 96.52 KWH; Using our high-speed nail making machine, according to the actual operation of 3.8Kw calculation, about the need for electricity 53.9 KWH, the actual saving of electricity up to 42.62 KWH;

The waste nail loss is reduced to about 1%, about $6;

The consumption cost of mold, nail cutter and punch should be reduced by more than 70%, at least 2-3 dollars per ton. 

Because the quality of the nails produced is good, the efficiency of the coil nail is 25% to 45% higher, and the labor cost is reduced by at least $6 / ton. If you can use clean wire, you don't need to wash the nails anymore, and you save another $5 or so per ton.

Compared with the common nail making machine, the comprehensive cost per ton of nails is reduced by more than 26 dollars, which can save more than 7,800 dollars a year.

Save the site (the same site can produce more nails), No more worries about the management of workers(Any worker can be trained for 2 days and become proficient), absolutely stable and reliable nail quality, can be assured to boldly accept any high demand high profit orders! Thus there are endless relatively high profit orders!

Models & Parameters

The machine's main characteristics are as following:

1.Shorter stroke (12mm), traditional machine around 100mm

a.Stable performance, defective rate less than 1/100000

b.Lower mechanical wear

c.Gripping dies and punches are more durable.

2.The nail length can be well controlled.

a.The machine equipped with sensor for detecting longer or shorter nails

b.Active wire feeding, can ensure straight shank and consistent length, no matter what the wire coil's weight is.

3.Metal scraps can be separated with nails very well

a.Effectively protect the nail conveying belt

b.Ensure the good shape nail head

Unique Features

1) Dual-mode double-punch

2)Nail blade holder uses the pendulum structure

3) Feeding and rewinding structure

Customer Visiting

Packing & Delivery

Contact person: Helen

Email:export@3shardware.com

phone : 0086-551-82819016

Whatsapp & Moble :+8618556536386

Skype: helenlee558